液壓配件與維修

產品描述

 夯錘的知識分享：后排夯錘的下止點應和熨平板平或者比熨平板略低但不應超過0.5mm。后排夯錘下止點過高過低都會影響攤鋪質量。夯錘越重，對橋臺的振動影響越大，且夯沉量隨夯擊次數的增加而增大，合適的錘重和夯擊次數可有效控制對橋臺的動力影響；夯錘前擋板與夯錘間應有0.5 mm的間隙。間隙過小夯錘前擋板推料引起變形后會夾住夯錘使夯錘軸轉動困難。間隙過大則容易進料，加快夯錘、夯錘前擋板、磨損條的 磨損，同時進料也會影響夯錘軸的轉動。

免責聲明丨 部分內容來源網絡！本文僅供交流學習 , 版權歸屬原作者，部分圖片、內容推送時未能及時與原作者取得聯系，若來源標注錯誤或侵犯到您的權益煩請告知，我們將立即刪除.

企業介紹

公司供應攤鋪機配件，壓路機配件，銑刨機配件，攤鋪機刮板驅動軸，刮板驅動軸總成，找平儀，找平儀支架以及液壓泵和配件。還供應攤鋪機易損件，攤鋪機平衡梁，攪龍軸，踏板，輸料底板，葉片，熨平板，減速機，鏈軌，履帶板，支重輪，刮板大鏈條，輸料鏈條等。

聯系人：梁經理

聯系方式：13645201509（微信同號）

QQ：2870202745

QQ郵箱：2870202745@qq.com

網易郵箱：LS13645201509@163.com

WhatsApp:+86  13645201509

Knowledge sharing of chain wheel rammer on scraper: The bottom stop point of the rear rammer should be level with the ironing board or slightly lower than the ironing board but should not exceed 0.5mm. If the bottom stop point of the rear rammer is too high or too low, it will affect the paving quality. The heavier the rammer, the greater the impact on the vibration of the bridge pier, and the settlement of the rammer increases with the increase of the number of ramming times. Appropriate hammer weight and ramming times can effectively control the dynamic impact on the bridge pier; There should be a gap of 0.5 mm between the front baffle of the rammer and the rammer. If the gap is too small, the front baffle of the rammer will deform and clamp the rammer, making it difficult for the rammer shaft to rotate. If the gap is too large, it is easy to feed and accelerate the wear of the rammer, rammer front baffle, and wear strip. At the same time, feeding will also affect the rotation of the rammer shaft.

Disclaimer | Some content is sourced from the internet! This article is for communication and learning purposes only. The copyright belongs to the original author. Some images and content were not promptly contacted when pushed. If the source annotation is incorrect or infringes on your rights, please inform us and we will immediately delete it

Company Introduction

The company supplies paver accessories, roller accessories, milling machine accessories, paver scraper drive shaft, scraper drive shaft assembly, leveling instrument, leveling instrument bracket, hydraulic pump and accessories. We also supply vulnerable parts for pavers, including balance beams, agitator shafts, pedals, feeding base plates, blades, ironing plates, reducers, chain rails, track plates, support wheels, scraper chains, and feeding chains.

Contact: Manager Liang

Contact information: 13645201509 (same WeChat account)

QQ：2870202745

QQ email: 2870202745@qq.com

NetEase email: LS13645201509@163.com

WhatsApp:+86  13645201509